Showing results: 91 - 105 of 132 items found.
-
DN2.445-02 -
Spectrum Instrumentation
The digitizerNETBOX DN2.44x series allows recording of one, two, four or eight synchronous channels with sampling rates of 130 MS/s up to 500 MS/s. These products offer outstanding A/D features in resolution, bandwidth and speed as a remote instrument. The powerful A/D amplifier section offers six different input ranges, two input paths, AC/DC coupling and noise reduction filters.
-
Model 2215 -
Empower RF Systems, Inc.
The 2215 is suitable for octave bandwidth high power CW, modulated, and pulse applications. This amplifier utilizes high power GaN devices that provide wide frequency response, high gain, high peak power capability, and low distortions. Exceptional performance, long-term reliability and high efficiency are achieved by employing advanced broadband RF matching networks and combining techniques, EMI/RFI filters, and all qualified components. The amplifier is constructed within a single 5RU drawerincluding the forced air-cooling. Available operating voltage configurations are single-phase 220 VAC up to 400 Hz and 28 VDC.
-
5147 -
Abaco Systems Inc
ECM P/N 5147 provides two channels of 12 bit A/D conversion using the Analog Devices AD9235, and is suitable for medium resolution high speed applications. The two differential inputs are terminated in 120 ohms and buffered with a gain of 1 differential amplifier. Differential Input range is +/-3.0V. Sample rates are 20MHz per channel with a 5MHz 4 pole elliptical analog input filter.
-
Pacific Instruments, Inc.
Series 6800 for laboratory applications is a ready-to-run, high performance measurement system. Enclosures are 3U rack mountable or can be used right on the desktop. 6800 units come equipped with a conditioner, amplifier, filter and digitizer. Each channel has a front mounted connector specific to a measurement type: RJ-45 for 8-wire bridge transducers, BNC for voltage or ICP/IEPE inputs or a 3-wire military grade connector.
-
N5173B -
Keysight Technologies
Balance budget & performance to address parametric testing of microwave components & receiversPerform LO up conversion for microwave backhaul links or CW blocking for receiver testingMaximize test throughput with 600-s frequency switchingCharacterize microwave filters & amplifiers with the best combination of output power, low harmonics & full step attenuationUse as a high-stability system reference: the standard high-performance OCXO has an aging rate of 5x10-10 parts/day
-
ICE3009 -
Pole/Zero
The ICE3009 subsystem is an agile filter for the VHF-L, VHF-H and UHF frequency bands. It allows operation of a number of transceivers in a cosite environment. The VHF/UHF Filter provides multiple poles of RF selectivity to reduce broadband noise in transmit mode of operation and to reduce interfering signals at the transceiver’s RF input in receive mode at Have Quick II/IIa and SATURN tuning speeds. This design incorporates a flexible control scheme that can be configured at the factory for various radio interfaces (ARC-210, ARC-231, ARINC 429, etc.). The design is highly integrated and includes all filters, amplifiers, power supply, transmit and receive switching (including a bypass mode), and Built-in-Test (BIT). A mounting tray is available as an option for easy incorporation on your platform. This system is qualified for military applications. Cost-effective modifications are available on the ICE3009. Please contact your sales representative at 513.870.9060 or Support@PoleZero.com for details.
-
WMA-005 And WMA-005LF -
Falco Systems
The Falco Systems WMA-005 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-005LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
WMA-01 And WMA-01LF -
Falco Systems
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
WMA-02 And WMA-02LF -
Falco Systems
The Falco Systems WMA-02 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 4mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-02LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.2mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Pacific Instruments, Inc.
Series 6800 for portable applications is a ready-to-run, high performance measurement system that is DC powered for mobile applications. All connections are front mounted for easy installation in tight places or on the go. 6800 systems come equipped with a conditioner, amplifier, filter and digitizer. Each channel has a front mounted connector specific to a measurement type: RJ-45 for 8-wire bridge transducers or BNC for voltage or ICP/IEPE inputs.
-
Kuhne electronic GmbH
. Internal filters provide high spurious rejection and image rejection. Due to low phase noise and high frequency stability of the local oscillator at 3000 MHz, the up converter is suitable for analog and digital communication systems.Typical applications are Multichannel Multipoint Distribution Systems (MMDS) using QPSK modulation and DVB?T or DVB?S systems. The output power of 20 mW can be increased to several watts by the use of an additional power amplifier.
-
Optilab, LLC.
A line of Gain Flattening Erbium-Doped Fiber Amplifiers are designed for in-line amplification of DWDM networks. When a standard EDFA is used to amplify multi-channel DWDM signals, the output power level of various channels will vary according to the gain profile of the erbium fiber. This gain variation can be as great as 6 dB in magnitude. The EDFA-GB-R is unique in its dual-stage amplification and internal Gain Flattening Filter (GFF) to compensate the erbium fiber gain variation.
-
ERAVANT
Phase locked oscillators (PLO) utilize state-of-the-art planar circuits, three-terminal devices and dielectric resonator technology to generate high-quality microwave signals at lower frequencies. Frequency multipliers, amplifiers and filters are used to extend the low frequencies for higher frequency requirements. The standard offering covers the frequency range of 2 to 110 GHz and provides both internal and external reference options. The frequency stability and phase noise are dependent on the oscillator reference type.
-
28000 -
Precision Filters, Inc.
The Precision 28000 Signal Conditioning System makes it easy to manage a test with up to 256 channels of fully programmable transducer conditioning. Choose a mix of bridge, charge, IEPE w/TEDS, voltage (filter amplifier), strain, thermocouple, RTD/potentiometer, frequency, or other transducers. Self-tests traceable to NIST. 4, 8 and 16-slot rugged and transportable mainframes feature integrated cooling. Customize the 28000 for high-speed transient applications, static applications, or a combination of both.
-
SA1022 -
Hangzhou Softel Optic Co., Ltd.
*1000MHz Broadband RF signal amplifier, Line extender, RF amplifier GaAs MMIC used on the forward path, Power-Double module amplify module are used as output stage, Output level is stable and nonlinear index is good, import high index amplify module are used on return path, its distortion is little and SNR is high.*It is more convenient to debug because of plug-in (or adjustable) duplex filters, plug -in fixed (or adjustable) equalizers, plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
